PDA

View Full Version : for sale: Slee 80 Series Transfer Case Skid Plate


Hulk
03-29-2007, 03:12 AM
Skid plate was installed on my 80 for less than a year. Paint is scratched in one spot. All hardware included. Easy to install, and it is extremely stout. Details on Slee Offroad web site here (http://sleeoffroad.com/products/skid_main.htm). It's black, not red.

Original price: $139 + tax.
Asking: $85.

Uncle Ben
03-29-2007, 09:23 AM
Skid plate was installed on my 80 for less than a year. Paint is scratched in one spot. All hardware included. Easy to install, and it is extremely stout. Details on Slee Offroad web site here (http://sleeoffroad.com/products/skid_main.htm). It's black, not red.

Original price: $139 + tax.
Asking: $85.

Watcha replace it with? :confused:

Shark Bait
03-29-2007, 09:49 AM
PM sent.

nakman
03-29-2007, 09:57 AM
Coool, you getting an IPOR?

Shark Bait
03-29-2007, 10:34 AM
I would too if I could afford one. :o

Hulk
03-29-2007, 11:39 AM
Coool, you getting an IPOR?

Yes. :)

Watcha replace it with? :confused:

Go here (http://www.ironpigoffroad.com/armor/skidplates.shtml) and scroll down a bit.

http://www.ironpigoffroad.com/armor/skidplateimg/80skid2.JPG

Installed last night at Ben's garage. :thumb:

nakman
03-29-2007, 12:10 PM
Cool! I'm curious what this sucker weighs, any idea? And how much did the crossmember weigh? And what did you do with all those undercarriage lighting wires that you had running through that crossmember you took off... oh wait that's my 80 :rolleyes:.

hey good looking web site over there at ipor... ;)

Three Wheel Ben
03-29-2007, 01:07 PM
Cool! I'm curious what this sucker weighs, any idea? And how much did the crossmember weigh?

It's pretty damn heavy!! At least twice as heavy as the slee/crossmember combo.

Shark Bait
03-29-2007, 01:35 PM
It's pretty damn heavy!! At least twice as heavy as the slee/crossmember combo.

So you think it's worth it, in your professional opinion? ;)

Beater
03-29-2007, 02:09 PM
what supports the t-case cover from deflection?

Three Wheel Ben
03-29-2007, 02:50 PM
So you think it's worth it, in your professional opinion? ;)

It's what I'm basing the on I'm in the process of putting together for my 100 on. :bowdown:

Three Wheel Ben
03-29-2007, 02:54 PM
what supports the t-case cover from deflection?

3/8" , I don't think it is going anywhere. Plus you don't have to worry about getting hung up on the x-member.

Shark Bait
03-29-2007, 04:16 PM
It's what I'm basing the on I'm in the process of putting together for my 100 on. :bowdown:

O a. :D

Beater
03-29-2007, 07:07 PM
hmm.. .0375 vs. 6400lbs as a support point, but you are a wwwaaaaayyyyy better driver than me. I wouldn't do it, but then again, I couldn't drive a stock 100 through half the crap you do and make it out un-scathed!

I am sure it's fine... in fact, more than fine. My only thought would be if it did bend, at .0375, without a big press, it's not coming back to shape.

nakman
03-29-2007, 09:53 PM
Hey 3/8 is .375", aka an eighth away from a half inch. But I can see your point... would be fun to put a floor jack under that thing then lift the truck up, see what deflects.