PDA

View Full Version : I need money...


Squishy!
07-20-2007, 06:25 PM
If you want to give me some that would be great! :lmao: But I'm willing to work for it... :D

I'm an employee of a Toyota dealership, so i'm trained especially them. Hooray! There is a whole lot I can do at home, but a lot that I don't have the resources for. Like Diagnostic stuff. But maintenance stuff is usually fine.

So PM me or call me at 303.895.7944 and leave a message if I don't answer and I'll tell ya if I can do it. Sweet. Thx.

:thumb:

Shark Bait
07-20-2007, 07:31 PM
How much to replace the head gasket on an 80 and get it running? :D

http://www.risingsun4x4club.org/forum2/showpost.php?p=41170&postcount=4

treerootCO
07-20-2007, 08:14 PM
I have 40 tires that need to be broken down

acon40
07-20-2007, 08:19 PM
i just need a look over....tell me what i need to service or replace on a new to me rig.....

Crash
07-20-2007, 09:54 PM
How about assisting with the rebuild of a split case transfer behind a new A440F arriving from OZ in a month or two?

calphi27
07-22-2007, 06:38 PM
How about assisting with the rebuild of a split case transfer behind a new A440F arriving from OZ in a month or two?

Did you get one of rodney's extreme trannys? Trasmission that is.:D

nakman
07-23-2007, 08:31 AM
Squishy I've got some stuff you could probably do... PM sent! ;)

JadeRunner
07-23-2007, 12:05 PM
I'll see if my Dad would be instersted in having you install his EV only switch in the glovebox on his Prius. He has the instructions. It's supossed to be a 45 minute job.

Ron Helmuth
07-23-2007, 01:57 PM
Dual guages (A) pillar pod for a 99 Runner-electrical senders only-no mechanical

are you interested? Oil pressure and water temp likely are the gauges.

nakman
08-02-2007, 10:11 PM
quick bump for Squishy.. my 80 now has a new water pump, new coolant, and no drips. He even let me help a little.. thanks again, Justin! :thumb:

treerootCO
08-05-2007, 01:17 AM
I'll give you $100 if you can come over tomorrow and help reglaze all my exterior windows. I'll show you how if you have never done it before....

timmbuck2
08-05-2007, 07:49 AM
I will need my PHH on my 80 done soon...and of course the HG someday. :) Any idea how to put a 2F into a 40? :)

T

corsair23
08-05-2007, 10:42 PM
I will need my PHH on my 80 done soon...and of course the HG someday. :) Any idea how to put a 2F into a 40? :)

T


Oooooh...PHH :D

I've got 2 of them to do :(. Not that I really want to miss out on the fun of doing them but how much would you charge to replace the PHH and do a cooling system flush at the same time?

Three Wheel Ben
08-06-2007, 07:20 AM
I will need my PHH on my 80 done soon...and of course the HG someday. :) Any idea how to put a 2F into a 40? :)

T


Do you want me to return the hose I picked up for you?:D

Squishy!
08-06-2007, 03:26 PM
Wow I feel ignorant. What is a PHH.

Oooooh...PHH :D

I've got 2 of them to do :(. Not that I really want to miss out on the fun of doing them but how much would you charge to replace the PHH and do a cooling system flush at the same time?

Shark Bait
08-06-2007, 03:43 PM
PHH (http://forum.ih8mud.com/showthread.php?t=6994) :rolleyes: :D

sno bored
08-06-2007, 03:48 PM
PHH, Problem Heater Hose. It's a small hose on the bottom of the 80 series motor. It's a pain to get your hands in there because there is not much room. Some people drop their starter motor to give more room. I just pulled my trans. dipstick to do mine. There are lots of posts on MUD on what tools work best.

Squishy!
08-06-2007, 03:50 PM
Ok... So what is it? all I'm getting from Mud is that I should use green stripe on my Cruiser... wait. I haven't been cursed with one of those. Hooray!

:lmao:

wesintl
08-06-2007, 04:19 PM
http://sleeoffroad.com/technical/tz_heater_hose.htm

nakman
08-06-2007, 04:30 PM
Squishy this one could be a good opportunity for you, just need to get the technique down. It takes most mortals about a half day to do this..

:robbie: can do one in 30 minutes. :bowdown:

so if you could get the process down, with coolant swap, you should have a decent amount of interest. And hey you already know where the block drain is! ;)

corsair23
08-06-2007, 04:55 PM
I agree with Tim :)

Many choose to go with these - http://www.1fzfephh.com/ - so as to not have to worry about it again for a lonnnnng time. It is one of those things that has to be done, almost like a right of passage, but IMO doesn't add much to learning about your Cruiser. As for flushing the coolant, well IMO that is an easy job just a big PITA because of trying to get rid of the old coolant. Seems no one really wants to take it, unless you are paying them to do the flush :(

I'm more than willing to let you "hone" your skills on my rigs to see if you can get down to the 30 min range :thumb: :lol: