Rising Sun Member Forums

Rising Sun Member Forums (http://www.risingsun4x4club.org/forum2/index.php)
-   Trip and Event Reports (http://www.risingsun4x4club.org/forum2/forumdisplay.php?f=4)
-   -   Yankee Hill & Miner's Gulch 10/8/05 (http://www.risingsun4x4club.org/forum2/showthread.php?t=318)

Bobzooki 10-10-2005 08:13 AM

Yankee Hill & Miner's Gulch 10/8/05
 
Well, my guests for the weekend brought the expected 98 TJ, and a Honda Rincon Quad, and also a guest from Boston, in a TJ, so we played in the back yard...

Ran into Brant from the Clear Creek Ranger District, and chatted for awhile. Miner's Gulch is a nice side trip - I hadn't run it before.

Yankee Hill is much easier than it was two years ago - I don't think I even had the lockers on. In fact, the entire run seemed much easier than before - maybe it's the 4Runner CV axles...

Had to winch a kid in a Nissan (I think - would that be a Pathfinder?) out of a mine "test hole". He blasted over the lip, and was in the hole before he knew it, and fully supported on his front and rear bumpers, with his wheels barely touching the dirt. (Shaking Head)...

Hopefully, I'll have pics in a day or so, of the pint-sized Gnewt winching this fool out of the hole.

Uncle Ben 10-10-2005 10:20 AM

Quote:

Originally Posted by Bobzooki
Well, my guests for the weekend brought the expected 98 TJ, and a Honda Rincon Quad, and also a guest from Boston, in a TJ, so we played in the back yard...

Ran into Brant from the Clear Creek Ranger District, and chatted for awhile. Miner's Gulch is a nice side trip - I hadn't run it before.

Yankee Hill is much easier than it was two years ago - I don't think I even had the lockers on. In fact, the entire run seemed much easier than before - maybe it's the 4Runner CV axles...

Had to winch a kid in a Nissan (I think - would that be a Pathfinder?) out of a mine "test hole". He blasted over the lip, and was in the hole before he knew it, and fully supported on his front and rear bumpers, with his wheels barely touching the dirt. (Shaking Head)...

Hopefully, I'll have pics in a day or so, of the pint-sized Gnewt winching this fool out of the hole.

You will find that with each Toyota part added the Gnewt will respond with more "authority!" :D

Bobzooki 10-10-2005 11:07 AM

Quote:

Originally Posted by Uncle Ben
You will find that with each Toyota part added the Gnewt will respond with more "authority!" :D

So I should have tried to get that mirror, for a 40, at the meeting???

;)

Uncle Ben 10-10-2005 12:16 PM

Quote:

Originally Posted by Bobzooki
So I should have tried to get that mirror, for a 40, at the meeting???

;)

Exactly! Maybe some floor mats too!

Rzeppa 10-10-2005 05:43 PM

Quote:

Originally Posted by Uncle Ben
You will find that with each Toyota part added the Gnewt will respond with more "authority!" :D

How about a 1FZ in that sucker, or even a 2UZ! :-)

Bobzooki 10-11-2005 08:00 AM

Quote:

Originally Posted by Rzeppa
How about a 1FZ in that sucker, or even a 2UZ! :-)

I don't know EXACTLY what those are, but I think I've got a 3S-FE in my Camry, so I'm gonna have to say that I'll stick with my 158 pound 1.6 L I4 with 96 pale, thin, wheezing ponies - well that and a 90:1 final gear ratio.

I'm about to replace the factory ECM with a DIY MegaSquirt ECM - just started building it. Then we'll see what that little engine can do, once I've got complete control of the timing and mixture curves!


All times are GMT -6. The time now is 09:08 PM.

Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.