Rising Sun Member Forums  

Go Back   Rising Sun Member Forums > Toyota 4x4 > General Tech Forum

Reply
 
Thread Tools
  #1  
Old 07-07-2012, 05:12 PM
Phrog Phrog is offline
Lifted
 
Join Date: Mar 2007
Location: Boulder
Posts: 144
Default dizzy bolt size and access?

I'm trying to remove the distributor from my 1976 FJ40 (replacing it with a DUI).
-What's the size of the hold-down bolt (I think it's 11 or 12 mm)?
-Is there any easy way to access it? My crescent wrench
hits the oil filter, and my socket is obstructed by the dizzy body.

Only solution I can think of is to order a "crows foot wrench" of the
appropriate size.

-Phrog
Reply With Quote
  #2  
Old 07-07-2012, 05:25 PM
kurtnkegger's Avatar
kurtnkegger kurtnkegger is offline
Rising Sun Member
 
Join Date: Jan 2011
Location: Denver Burbs
Posts: 257
Default

Mine is a 10mm, yours might be different if a substitute non-JIS bolt were used. Try a small extension on your socket, or what I do, is use a ratchetting wrench flipped over to avoid the dizzy diaphram and loosen/tighten a little at a time. GL
Reply With Quote
  #3  
Old 07-07-2012, 05:31 PM
RicardoJM's Avatar
RicardoJM RicardoJM is offline
Rising Sun Member
 
Join Date: Jul 2007
Location: Centennial, CO
Posts: 2,301
Default

I seem to recall it is a 10mm. I have the plates (small plates that keep mud from splashing up) removed and can easily access the bolt from under the truck. That said, I also can access it from the top pretty easy. Use a 12 point combination wrench which will work very well.
__________________
Ricardo Maestas - Bio Page
KD0CAW
1999 LX 470, 1971 FJ-40
TLCA #18941
Reply With Quote
  #4  
Old 07-08-2012, 07:33 AM
Jacket's Avatar
Jacket Jacket is offline
Rising Sun Member
 
Join Date: Feb 2007
Location: Lafayette
Posts: 4,008
Default

I think it's a 12mm (head size) on mine. I used a combo wrench like Ricardo, accessing it from in between the oil filter and the dizzy.
__________________
- Matt
1976 FJ40 - green and mostly stock
1996 FZJ80 - not so stock
Reply With Quote
  #5  
Old 07-08-2012, 12:18 PM
Phrog Phrog is offline
Lifted
 
Join Date: Mar 2007
Location: Boulder
Posts: 144
Default Dizzy

Well I loosened the clamp that goes around the dizzy, and once that was loose the dizzy slid right out. Then of course I had direct access to the bolt.

Now on to installing the DUI. Seems straightforward...I'll post up the results.

Phrog
Reply With Quote
  #6  
Old 07-11-2012, 05:21 PM
Rzeppa's Avatar
Rzeppa Rzeppa is offline
Cruise Moab Committee
 
Join Date: Aug 2005
Location: Kittredge CO, USA
Posts: 5,194
Default

It is a 12 MM hex head (M8). The 10mm (M6) is the one that locks rotation.
__________________
Jeff Zepp
Kittredge CO USA
1971 & 1976 FJ40s, 1978 FJ45, 1987 FJ60
Rising Sun 4WD Club, TLCA #4063
http://american3dprinting.net/
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:34 AM.


Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.