Rising Sun Member Forums  

Go Back   Rising Sun Member Forums > For Sale + Help > For Sale / Wanted

Reply
 
Thread Tools
  #1  
Old 07-13-2013, 03:57 PM
FJ_Mark FJ_Mark is offline
Lifted
 
Join Date: Feb 2007
Location: Littleton, CO
Posts: 152
Default Garage clean out / moving sale

I'm moving to Texas soon and. Need to lighten the load. Whatever doesn't sell goes in the trash.

Snapon engine stand. This one has a gear drive crank to turn the motor on the stand. It also folds flat when you are not using it. The are about $650 new. I'm asking $200. Sold.

Small block Chevy plug wire loom. $5 sold

Crank handle for Cruiser bottle jack. $5 sold

Overhaul kit for split case transfer. $25 sold

Fj62 rear frame member. $20 obo. Sold

E-brake pivot boot. $5 sold

Fenders for trailer. I thnk these fit the Canadian 1/4 ton. Free to good home. Sold

Bucket-o stuff. Misc stuff I have collected in my tool box. 12 pack of Belgian white. White rascal preferred Sold

FJ60 outer rocker panel. $20

Big shop fan. Works great I just don't want to move it again. $25

FJ cruiser complete front bumper. Free to good home.
Attached Images
      

Last edited by FJ_Mark; 08-19-2013 at 01:39 PM. Reason: Showing sold items
Reply With Quote
  #2  
Old 07-13-2013, 03:58 PM
FJ_Mark FJ_Mark is offline
Lifted
 
Join Date: Feb 2007
Location: Littleton, CO
Posts: 152
Default

I will have to add the rest of the photos later. I can only get one to upload.
Attached Images
    

Last edited by FJ_Mark; 07-13-2013 at 06:14 PM.
Reply With Quote
  #3  
Old 07-13-2013, 05:30 PM
nuclearlemon's Avatar
nuclearlemon nuclearlemon is offline
Hard Core 4+
 
Join Date: Aug 2005
Location: denver
Posts: 5,708
Default

what era crank handle (yellow cast or brown stamped)?

might be interested in the engine stand too, need to talk to other half
__________________
ige tlca #1431
Reply With Quote
  #4  
Old 07-13-2013, 06:06 PM
FJ_Mark FJ_Mark is offline
Lifted
 
Join Date: Feb 2007
Location: Littleton, CO
Posts: 152
Default

The handle is yellow cast.
Reply With Quote
  #5  
Old 07-13-2013, 07:23 PM
nuclearlemon's Avatar
nuclearlemon nuclearlemon is offline
Hard Core 4+
 
Join Date: Aug 2005
Location: denver
Posts: 5,708
Default

i'll take the handle. where in littleton? would it have to be picked up evenings or daytime/
__________________
ige tlca #1431
Reply With Quote
  #6  
Old 07-13-2013, 07:36 PM
FJ_Mark FJ_Mark is offline
Lifted
 
Join Date: Feb 2007
Location: Littleton, CO
Posts: 152
Default

Near broadway and belleview. I should be home this week. I will pm you my number.
Reply With Quote
  #7  
Old 07-14-2013, 07:42 AM
cbmontgo's Avatar
cbmontgo cbmontgo is offline
Hard Core 4+
 
Join Date: Dec 2007
Location: Larkspur, CO
Posts: 849
Default

Ill take those trailer fenders if you can wait a week or so for me to pick them up?
__________________
'73 FJ40
'76 FJ40
'96 FZJ80
'00 UZJ100
Reply With Quote
  #8  
Old 07-14-2013, 08:17 AM
FJ_Mark FJ_Mark is offline
Lifted
 
Join Date: Feb 2007
Location: Littleton, CO
Posts: 152
Default

Quote:
Originally Posted by cbmontgo View Post
Ill take those trailer fenders if you can wait a week or so for me to pick them up?
No problem. I'm not leaving till end of August or early sept.
Reply With Quote
  #9  
Old 07-14-2013, 03:05 PM
RedCreeper's Avatar
RedCreeper RedCreeper is offline
Hard Core 4+
 
Join Date: May 2008
Location: Firestone, CO
Posts: 897
Send a message via AIM to RedCreeper
Default

I will take the chevy wire loom.
__________________
Kenny Jones
TLCA #19056
08 TT FJC
82 Scrambler (Scraps)
81 Scrambler (Sassy)
07.5 Dodge Ram 2500
69 Maro... next project when the Jeeps get done.....
Reply With Quote
  #10  
Old 07-14-2013, 05:21 PM
74fj40's Avatar
74fj40 74fj40 is offline
Hard Core 4+
 
Join Date: Oct 2005
Location: Highlands Ranch, CO
Posts: 879
Send a message via AIM to 74fj40 Send a message via MSN to 74fj40
Default

ill take the rear frame member
__________________

1997 Honda civic DX( all stock DD)
1972 Toyota FJ40(4" lift, FJ60 axles, FJ60 4speed with split case, 35's, Detroit locker rear, Lockright front, Marlin Highsteer, 105"WB, Saginaw with GM tilt column, soon to have: 30spline longfields, inners/outters, toybox.
1967 Porsche 912(100% stock)


[/font]
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -6. The time now is 12:36 PM.


Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.