Rising Sun Member Forums  

Go Back   Rising Sun Member Forums > Toyota 4x4 > General Tech Forum

Reply
 
Thread Tools
  #1  
Old 07-26-2010, 07:08 PM
yotarunner84 yotarunner84 is offline
Rock Stacker
 
Join Date: Jul 2010
Location: Englewood
Posts: 4
Default Lift Kits

Hey I just got a 84 4runner about a week ago and the lift the owner put on seems kind of sketch to me. It's a 4 inch shackle lift with stock leaf springs. I want to replace it but don't wanna spend alot of money on suspension parts. If anyone has or knows of or where to get a good cheap lift or advice of what to do it would be greatly appreciate.

Thanks everyone
Tony
Reply With Quote
  #2  
Old 07-26-2010, 07:23 PM
coax's Avatar
coax coax is offline
Hard Core 4+
 
Join Date: Oct 2008
Location: Estes Park
Posts: 600
Default

Not much experience w/ leafs, but a 4" shackle lift sounds super sketchy to me. Maybe someone on the forum has some springs to sell, or you could look at an add-a-leaf?
__________________
-Corey
'97 lx450, 170k, factory lockers, ome 850/863, 285's, 4 working doors(1 more than the old fj55 )
'74 project pig (sold)
Reply With Quote
  #3  
Old 07-26-2010, 10:28 PM
TIMZTOY's Avatar
TIMZTOY TIMZTOY is offline
Hard Core 4+
 
Join Date: Apr 2009
Location: Denver
Posts: 1,884
Default

his truck is actually sitting in my driveway, as i work on it.. i pulled the head off friday morning. and concluded that him buying a used motor is faster and more cost effective right now and then rebuild the old motor were pulling out.

he actually has stock springs inthe front, with about 4-6" shackels in the front with the springs at negative arch about 2" sitting static.. and the rear is at flat arch or no arch, with 12-14" homeade shackels in the rear super scarry.. even if someone had a pare of stock springs laying around that we could slap on there to get rid of the negative arch, that would be apriceated

tony place a new post in the forsale section
__________________
TLCA # 20314
84 Hilux, 22re Conversion, 63" chevy rears, Rears up front, Bobbed bed, duel e-lockers, 5.29's, 35" Ground Hogs low compression
Step by Step Bed Bob
Reply With Quote
  #4  
Old 07-26-2010, 11:30 PM
TonkaToy's Avatar
TonkaToy TonkaToy is offline
Rising Sun Member
 
Join Date: Jul 2010
Location: Thornton, Colorado
Posts: 163
Default

I bought a used lift kit on Craig's list for my FJ40, from a memeber in here, as it turns out. You may want to check that out or check with the Yota Yard for a used set. I would sooo not be driving it like it is!
Reply With Quote
  #5  
Old 07-27-2010, 06:33 AM
MDH33's Avatar
MDH33 MDH33 is offline
Hard Core 4+
 
Join Date: Mar 2006
Location: Land of Corn
Posts: 5,767
Default

Marlin Kit
__________________
--Martin
Reply With Quote
  #6  
Old 07-27-2010, 09:04 AM
Air Randy's Avatar
Air Randy Air Randy is offline
Cruise Moab Committee
 
Join Date: Aug 2008
Location: Franktown, CO
Posts: 2,804
Default

The least expensive solution that gives you a pretty good off road suspension is to take the rear stock springs and move them to the front of the vehicle. This will also move the front axle forward 2" to help larger tires clear the firewall, but be sure and check the engagement of the driveshaft splines afterwards.

Then go to a junk yard and get a set of rear leaf springs out of a late 80's to early 90's chevy 1/2 ton pickup. Install those in the rear. You will have to relocate the spring hanger a few inches forward on the frame.

At that point the 4" shackles may be OK as long as the springs do not have negative arch. If the suspension is too high you can shorten the shackles by cutting them off and drilling new holes.
__________________
Randy Rosetta KDKWX TLCA #19351 69 FJ40 "Meanie" & 1970 Boss 302 Mustang
Reply With Quote
  #7  
Old 07-28-2010, 09:40 AM
RLMS's Avatar
RLMS RLMS is offline
Trail Ready
 
Join Date: Dec 2007
Location: Calhan Colorado
Posts: 320
Default

I have a set of aftermarket fronts we just pulled off, they had about an inch of lift in them still!!
75$

Justin
__________________
New> FJC rear lower link skids <New
Reply With Quote
  #8  
Old 07-28-2010, 06:31 PM
BreckBJ44's Avatar
BreckBJ44 BreckBJ44 is offline
Trail Ready
 
Join Date: Sep 2007
Location: On the road between Denver and Breckenridge
Posts: 376
Default

I'm sold on Alcan. Not the cheapest, but great customer service!

K
__________________
Kraig Hamady - Downtown Denver
1981 BJ44 RHD - Work in progress (or lack thereof)
Reply With Quote
  #9  
Old 07-28-2010, 10:00 PM
AxleIke's Avatar
AxleIke AxleIke is offline
Rising Sun Member
 
Join Date: Apr 2006
Location: Arvada, CO
Posts: 3,309
Default

Sigh...

You ALWAYS get what you pay for. If you want a cheap solution, you will get cheap results.

Nothing wrong with that, but don't expect to pay 300 bucks for a perfect suspension.

Marlin's kit is bomber, but it requires a lot of work, welding, etc...

IMO, marlin's is the min if you want a reliable DD/Weekend warrior.

Best advice/Cheapest advice: return it to stock, and wheel it. Wasting money on crappy suspension components that you will replace later due to garbage performance is pointless.

Just my .02.
__________________
Isaac

Baby Beast 2- 1999 4Runner SR5

Baby Beast -1987 4Runner SR5-Gone, but not forgotten

Generation Dead
Reply With Quote
  #10  
Old 07-28-2010, 10:28 PM
yotarunner84 yotarunner84 is offline
Rock Stacker
 
Join Date: Jul 2010
Location: Englewood
Posts: 4
Default

Alright, alright good advice but if marlin is the min what would you rec. putting on if I wanted better than marlin
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:11 AM.


Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.