Rising Sun Member Forums  

Go Back   Rising Sun Member Forums > Toyota 4x4 > General Tech Forum

Reply
 
Thread Tools
  #1  
Old 11-11-2006, 12:14 AM
Nick F.'s Avatar
Nick F. Nick F. is offline
Lifted
 
Join Date: Jun 2006
Location: Conifer
Posts: 189
Default t/c question

I got my transfer case off and torn apart. Shown is the hi/low clutch sleeve which is pretty worn. Is this way beyond reuse? I would like to replace it but the damn things are expensive.

Also shown is the high/low shift fork that is very worn on one side. The gap there measure about .120"

The p.o. had a bungie on the hi/lo lever keeping it forward from poping out of gear. Is the wear on the fork what causes it to pop out of gear? Has the bungie accelerated this wear? Also anyone have any idler gear thrust shims? I need .065" worth

Nick F.
Reply With Quote
  #2  
Old 11-11-2006, 01:26 AM
treerootCO's Avatar
treerootCO treerootCO is offline
Rising Sun Member
 
Join Date: Aug 2005
Posts: 4,569
Send a message via AIM to treerootCO
Default

you should replace it while you are in there. Part number 36235-60011 if I remember correctly and it wasn't that much.
My old one is on the left and the new one helped.
Attached Images
 
__________________
aka Mike D.----->Bio Page KDřGWY
“He who goes unarmed in paradise had better be sure that that is where he is.”—James Thurber
"Its better to be thought a fool rather than to speak up and remove all doubt." - Lincoln
pride is ego, the word I had lost was dignity. The quality or state of being worthy of esteem or respect.
Ptarmigan build thread - 95FZJ80
www.root45.com
www.risingsun4x4club.org

TLCA #14133

Reply With Quote
  #3  
Old 11-11-2006, 02:10 PM
Rzeppa's Avatar
Rzeppa Rzeppa is offline
Cruise Moab Co-Chairman
 
Join Date: Aug 2005
Location: Kittredge CO, USA
Posts: 5,381
Default

Yep, mine looked like that too. When I rebuilt the t-case I had to replace it as well as the high speed output gear. Cheap trick: You can turn it around to get rid of the slop where it engages with the gear, but it won't last as long as new. Aftermarket Seamaster are available (they are OE-supplier to Toyota) for less than Toyota. I got mine from Jim Sanborn, but he's out of the parts business. Rising Sun member Joe Calleja at CTS in Aspen Park deals in Seamaster and can probably set you up. (303) 838-4772.
__________________
Jeff Zepp
Kittredge CO USA
1971 & 1976 FJ40s, 1978 FJ45, 1987 FJ60
Rising Sun 4WD Club, TLCA #4063
http://american3dprinting.net/
Reply With Quote
  #4  
Old 11-11-2006, 05:27 PM
Nick F.'s Avatar
Nick F. Nick F. is offline
Lifted
 
Join Date: Jun 2006
Location: Conifer
Posts: 189
Default

Thanks guys,

I need a new high speed gear also. I was hoping to just throw a rebuild kit in it and be done, but it looks like I'm gonna need some extra parts. My toy fund is taking a beating but it makes no sense to do this all over again in a short amount of time.

Nick F.
Reply With Quote
  #5  
Old 11-11-2006, 05:46 PM
Rzeppa's Avatar
Rzeppa Rzeppa is offline
Cruise Moab Co-Chairman
 
Join Date: Aug 2005
Location: Kittredge CO, USA
Posts: 5,381
Default

Like I wrote, check out Joe at CTS, he'll probably be able to source you the parts.
__________________
Jeff Zepp
Kittredge CO USA
1971 & 1976 FJ40s, 1978 FJ45, 1987 FJ60
Rising Sun 4WD Club, TLCA #4063
http://american3dprinting.net/
Reply With Quote
  #6  
Old 11-11-2006, 06:01 PM
Nick F.'s Avatar
Nick F. Nick F. is offline
Lifted
 
Join Date: Jun 2006
Location: Conifer
Posts: 189
Default

Quote:
Originally Posted by Rzeppa
Like I wrote, check out Joe at CTS, he'll probably be able to source you the parts.
Will do, he's right down the road from me.

My high speed gear. The bushing is shot also, just rattles on the shaft
Reply With Quote
  #7  
Old 11-17-2006, 08:06 PM
Nick F.'s Avatar
Nick F. Nick F. is offline
Lifted
 
Join Date: Jun 2006
Location: Conifer
Posts: 189
Default

Hey Jeff,

Good call on cts. I got my parts today. It cost me less for new parts at cts than it would have for used at SOR

Thanks
Reply With Quote
  #8  
Old 11-17-2006, 08:10 PM
treerootCO's Avatar
treerootCO treerootCO is offline
Rising Sun Member
 
Join Date: Aug 2005
Posts: 4,569
Send a message via AIM to treerootCO
Default

SOR is a great place but....you HAVE to shop locally if you want to own a Cruiser. If you are a member of Rising Sun/TLCA you get discounts from the dealer as well. Have you called Boulder Toyota for parts yet? Stevenson and Burt also offer discounts. You may be surprised with the prices.
__________________
aka Mike D.----->Bio Page KDřGWY
“He who goes unarmed in paradise had better be sure that that is where he is.”—James Thurber
"Its better to be thought a fool rather than to speak up and remove all doubt." - Lincoln
pride is ego, the word I had lost was dignity. The quality or state of being worthy of esteem or respect.
Ptarmigan build thread - 95FZJ80
www.root45.com
www.risingsun4x4club.org

TLCA #14133

Reply With Quote
  #9  
Old 11-17-2006, 08:47 PM
Nick F.'s Avatar
Nick F. Nick F. is offline
Lifted
 
Join Date: Jun 2006
Location: Conifer
Posts: 189
Default

Quote:
Originally Posted by treerootCO
SOR is a great place but....you HAVE to shop locally if you want to own a Cruiser. If you are a member of Rising Sun/TLCA you get discounts from the dealer as well. Have you called Boulder Toyota for parts yet? Stevenson and Burt also offer discounts. You may be surprised with the prices.
So I'm finding out. Are any of the dealers better than the others? I tried calling stevenson for idler gear thrust washers and it didn't go too good.
Reply With Quote
  #10  
Old 11-17-2006, 08:55 PM
treerootCO's Avatar
treerootCO treerootCO is offline
Rising Sun Member
 
Join Date: Aug 2005
Posts: 4,569
Send a message via AIM to treerootCO
Default

Uncle Ben will post up here shortly. He is good friends with the parts guys at Boulder Toyota. Wes knows the guys at Burt. I shop with CDan in AZ because he knows me and my rigs. I honestly don't know the guys at Stevenson. My one experience with buying parts from them wasn't good but I owe them another shot.
__________________
aka Mike D.----->Bio Page KDřGWY
“He who goes unarmed in paradise had better be sure that that is where he is.”—James Thurber
"Its better to be thought a fool rather than to speak up and remove all doubt." - Lincoln
pride is ego, the word I had lost was dignity. The quality or state of being worthy of esteem or respect.
Ptarmigan build thread - 95FZJ80
www.root45.com
www.risingsun4x4club.org

TLCA #14133

Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:49 PM.


Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.